Stellar™ Portable Baby Bottle Warmer User Manual

1. Use this product only for its intended purpose.
2. Always operate this product under adult supervision. Keep it out of reach of children.
3. Do not allow to be used as a toy. Close attention is necessary when used near children.
4. Wash your hands before handling sterilized parts.
5. Do not expose the warmer to direct sunlight or heat for extended periods, as this may cause damage.
6. Place the device on a flat, stable surface when in use.
7. This device is designed for use with room-temperature or refrigerated liquids only. Do not use it with frozen breastmilk.
8. After heating, always check the liquid's temperature by placing a drop on the back of your hand.
9. Clean the product after each use, once it has cooled down.
10. Do not submerge the warmer in any liquid. To clean on the go, use a baby or breast pump wipe.
11. Avoid touching the stainless steel parts during heating, as they may cause burns.
12. Allow the warmer to cool down before cleaning.
13. Do not use corrosive cleaning agents, antibacterial cleaners, or high-concentration detergents, as they may cause plastic components to crack.
14. Do not charge the device if the main unit is wet.
15. Never operate this product if it has a damaged USB cord or plug, if it is not working properly, if it has been dropped nor damaged, or dropped into water.
16. Keep the cord away from heated surfaces.
17. Unplug the warmer when it is not charging. Extended time on the charger can lead to fires or other accidents.
18. Avoid overcharging and physical shocks (e.g., drops from high surfaces), as these may damage the warmer.
19. Do not attempt to access the interior of the device. Contact with electrical components may cause physical harm.
20. Failure to follow the warnings outlined in this IMPORTANT SAFETY INFORMATION section may result in harm to your health.

Your device is powered by a rechargeable battery. A USB-C cable and power adapter are included.

The USB charging port is located on the back of the warmer. When not charging, ensure the USB port cover is securely closed.

The device can be fully charged in approximately three hours. When the device is powered off, a quick press of the control button will display the battery life, ranging from 99% full to 20% low. During use, if the battery level drops below 20%, the display will flash “LO” to indicate that it’s time to charge.

Note: To avoid injury or damage, do not use incompatible, worn, or damaged batteries, chargers, or cables. Using other charging devices or batteries may void the warranty and cause damage to
the device.

The adjustment of voltage and output power depends on the connected device and is performed automatically.

To power on your Stellar™ Portable Baby Warmer, press and hold the control button located at the front of the device for two seconds. This will activate the device and enter Temperature Setting mode.

To power off, press and hold the control button again for two seconds. A single beep will indicate that the device is off.

The device offers four temperature settings: 37ºC, 40ºC, 45ºC, and 50ºC.

When powered on, the device enters Temperature Setting mode, automatically activating the last used temperature. To adjust to your desired temperature, press the control button again.

Once the desired temperature is reached, the warmer will emit a sequence of three beeps. The liquid will then be maintained at this temperature until the warmer is powered off.

Note: It is not recommended to prolong the keep-warm mode for breast milk beyond 20 minutes or to reheat breast milk more than once, as this may encourage bacterial growth.

Cleaning your Stellar™ at Home

1. Ensure the device has cooled down before cleaning.
2. Confirm that the USB port cover is securely closed and that the device is not charging.
3. Remove the silicone ring.
4. Carefully wash the silicone ring, then wipe down the warmer with a dishcloth. Finally, rinse off the warmer and dry it with the warming plate facing down.

Cleaning your Stellar™ on the Go

1. Ensure the warmer has cooled down and is not charging.
2. Confirm that the USB port cover is securely closed.
3. Remove the silicone ring and clean it carefully with a wipe.
4. Wipe down the inside of your Stellar™ warmer.

Cleaning Bottle Adapters

1. Remove the silicone ring.
2. Wash both the adapter and silicone ring gently with warm water and mild dishwashing detergent.
3. Let them air dry.

Caution: Never submerge your warmer in water, or place it in a microwave or dishwasher.

Note: When washing your warmer, always ensure the silicone port cover on the back is securely closed. Any liquid entering the battery compartment could damage the device.

We recommend sterilizing your bottle warmer as often as possible using either the traditional water and vinegar method or our Lumen™ Portable UV Sterilizer.

Stellar™ Portable Baby Warmer is compatible with leading European baby bottle brands and can be used with the following bottles:

No Adapter Needed: Philips AVENT.

Adapter Required: BIBS, Dr. Brown’s, Lansinoh, MAM, Medela, NIP, NUK First Choice, Suavinex Zero Zero, and Tommee Tippee.

The boil dry protection feature automatically turns off the heating element when no water is detected. The device will emit three beeps and display "HO" on the screen, indicating it has entered Boil Dry Protection mode.

To resume using the appliance, turn it off, fill the baby bottle with refrigerated or room temperature liquid, securely attach it to the warmer, and restart the device as usual.

To ensure the Stellar™ Portable Baby Bottle Warmer remains 100% leak-proof during warming and to protect the device from potential damage caused by liquid exposure, it's essential to use the appropriate sealing rings for both the heating plate and bottle adapters.

Both the heating plate and bottle adapters are equipped with food-grade silicone rings/gaskets. Before each use, check that these rings are in good condition and correctly inserted into the warmer and bottle adapter, if one is being used.

These sealing rings are wear-and-tear parts and should be replaced regularly. Additionally, it is crucial to use the bottle adapter that matches the brand of the baby bottle you typically use for feeding, as this helps prevent leaks and any associated damage.

In complience with 2012/19/EU Directive :

• All electrical or electronic devices must be disposed of separately from the municipal waste collection service, through collection points designated by the government or local authorities.
• Proper collection and treatment of obsolete devices help prevent potential risks to the environment and public health.
• For more information on how to dispose of obsolete devices, please contact your local council, waste collection service, or the retailer where you purchased the product.

At Cybele Star, we care deeply about the environment, and we appreciate your effort to dispose of all packaging in a safe and eco-friendly way.

• Cardboard Packaging: Please recycle in designated cardboard and paper recycling bins.
• Expanded Polypropylene (EPP): Dispose of it in the appropriate recycling bin according to your country’s waste classification rules.

Thank you for helping us protect the planet! 🌍

For optimal battery life and performance, fully charge your Stellar™ Portable Baby Bottle Warmer before its first use.

We recommend cleaning your Stellar™ Portable Baby Bottle Warmer prior to its first use. Refer to the detailed cleaning instructions provided.

As an additional step, we suggest sterilizing the heating area, the inserted sealing ring, and, if applicable, your bottle adapter. Sterilization can be done using either the traditional water and vinegar method, universal disinfecting wipes for babies or with our Lumen™ Portable UV Sterilizer.

1. Remove the dust cover.
2. Ensure the sealing ring is placed in the warmer with the smooth side facing down.
3. Check that the sealing ring in the bottle adaper is in place (If no adapter is needed, skip to STEP 5).
4. Secure the adapter by twisting it onto the bottle warmer, ensuring it is evenly threaded.
5. Add breast milk, formula milk or water to the bottle.
6. Flip your Stellar™ Portable Baby Bottle Warmer and attach to the top of the bottle. Make sure it is securely tightened and evenly threaded.
7. Once attached, flip the bottle warmer so the liquid touches the warming plate, and place it on a flat surface.
8. Four temprerature settings are available 37ºC, 40Cº, 45Cº or 50ºC. Hold down the control button for two seconds to begin temperature selection.
9. Once the desired temperature is reached, the warmer will beep three times. The liquid will be mantained at this temperature util the warmer is powered off.
10. To turn off the warmer, hold down the control button for two seconds.
11. Flip you Stellar™ Portable Baby Bottle Warmer and twist it off the bottle.
12. If using baby formula, add the desired amount of powder (if using breastmilk, skip to STEP 13).
13. Attach the baby bottle teat to the bottle and swirl the liquid.
14. After cleaning and sterilizing, place the dust cover back onto the device.