Lumen™ Portable UV Sterilizer User Manual

1. Use this product only for its intended purpose.
2. Always operate this product under adult supervision. Keep it out of reach of children.
3. Do not allow to be used as a toy. Close attention is necessary when used near children.
4. Eye damage may result from directly viewing the light produced by the lamp in this apparatus. Always turn off LED before opening the UV Lid.
5. UV light exposure may degrade plastic, fabric and rubber over time.
6. UVC light hazard. Do not look directly at UVC light while in operation.
7. Never use this device on pets or foods.
8. Do not tamper the lid interlocks to prevent UVC exposure.
9. This device should never be left unattended when plugged in.
10. Never operate this product if it has a damaged USB cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.
11. Keep the cord away from heated surfaces.
12. Place the device on a flat, stable surface when in use.
13. Do not submerge the device in any liquid.
14. Unplug the device when it is not charging. Extended time on the charger can lead to fires or other accidents.
15. Avoid overcharging and physical shocks (e.g., drops from high surfaces), as these may damage the device.
16. Do not attempt to access the interior of the device. Contact with electrical components may cause physical harm.
17. Failure to follow the warnings outlined in this IMPORTANT SAFETY INFORMATION section may result in harm to your health.

Your device is powered by a rechargeable battery. A USB-C cable and power adapter
are included.

The USB charging port is located on the left side of the sterilizer’s lid. While charging, a blue light on the top of the UV Lid will flash. Once fully charged, the blue light will remain steady. The device can be fully charged in approximately two hours.

Note: To avoid injury or damage, do not use incompatible, worn, or damaged batteries, chargers, or cables. Using other charging devices or batteries may void the warranty and cause damage to the device.

The adjustment of voltage and output power depends on the connected device and is
performed automatically.

To turn on your Lumen™ Portable UV Sterilizer, briefly press and hold the control button located at the top of the device. This will activate the sterilizer and initiate the default one-minute disinfection mode. A flashing indicator light signals that the device is on.

To turn off the device, press and briefly hold the control button again. A solid indicator light will confirm that the sterilizer is powered off.

Your Lumen™ Portable UV Sterilizer offers two disinfection settings: a one-minute mode and a three-minute mode.

• One-Minute Mode: Ideal for sterilizing a single small item at a time using the sterilizer box. This mode is perfect for pacifiers, bottle teats, or similar small objects.
• Three-Minute Mode: Recommended for sterilizing larger quantities or bigger items, using the UV light lid on its own or in conjunction with the silicone expansion pad. This mode is ideal for baby bottles, feeding accessories, our Stellar™ Portable Baby Bottle Warmer, and even portable baby food warmers.

Note: For optimal sterilization results when using the sterilizer box, do not insert more than one pacifier or other small objects at a time.

When powered on, the device automatically starts in one-minute disinfection mode. To switch to the three-minute mode, press the control button twice.

The indicator light will stop flashing and remain steady to indicate that the selected disinfection mode has completed successfully.

If no other action is taken within 30 seconds, the device will automatically power off.

Lumen™ Portable UV Sterilizer offers three versatile sterilization methods to cater to various needs:

1. Disinfecting with the Sterilizer Box: Ideal for quickly sterilizing small items like pacifiers, caps, or teats. A one-minute sterilization mode is sufficient for these.
2. Sterilizing with the UV Lid Alone: Perfect for larger items up to 72mm in diameter, such as baby bottles, water cups, Stellar™ Portable Baby Bottle Warmer, or other baby feeding accessories. Simply place the UV Lid on top and activate the three-minute disinfection mode.
3. Sterilizing with the Extension Silicone Pad: Suitable for items with larger surfaces, between 72mm and 130mm in diameter, such as baby bowls, cutlery, and portable baby food warmers, or for disinfecting multiple accessories at once. Assemble the UV Lid and Extension Pad, cover the items, and select the three-minute sterilization mode.

This device is not waterproof and should not be immersed in water.

To clean, wipe the surface of the unit with a dry towel, ensuring all water droplets are removed to prevent moisture from damaging the unit's circuitry.

The Extension Pad, made of silicone, can be washed by hand using warm water and a non-abrasive detergent.

Caution: Never submerge your sterilizer in water or place it in a microwave or dishwasher.

If lid is open during use, UV light will automatically turn off to protect skin and eyes from UV
exposure.

In complience with 2012/19/EU Directive :

• All electrical or electronic devices must be disposed of separately from the municipal waste collection service, through collection points designated by the government or local authorities.
• Proper collection and treatment of obsolete devices help prevent potential risks to the environment and public health.
• For more information on how to dispose of obsolete devices, please contact your local council, waste collection service, or the retailer where you purchased the product.

At Cybele Star, we care deeply about the environment, and we appreciate your effort to dispose of all packaging in a safe and eco-friendly way.

• Cardboard Packaging: Please recycle in designated cardboard and paper recycling bins.
• Expanded Polypropylene (EPP): Dispose of it in the appropriate recycling bin according to your country’s waste classification rules.

Thank you for helping us protect the planet! 🌍

Before first use, please remove the protective film inside the sterilizer box and on the underside of the UV lid.

For optimal battery life and performance, fully charge your Lumen™ Portable UV Sterilizer before its first use.

1. Clean the Item: Wash the item to be disinfected or wipe it clean to remove any debris before sterilization.
2. Prepare for Sterilization: Place the pacifier or teat nipple-side up into the Sterilizer Box, then cover it with the UV Lid.
3. Set Up the Device: Place the device on a flat surface.
4. Select Disinfection Mode: Briefly press and hold the control button at the top of the device to start the default one-minute disinfection mode. For a three-minute disinfection, press the control button twice. The indicator light will blink during the process.
5. Completion: When the selected disinfection mode is complete, the indicator light will stop flashing.
6. Retrieve the Item: Open the lid and remove the disinfected item.
7. Repeat if Necessary: The device is now ready to disinfect another pacifier or teat.

1. Clean the Item: Wash the item to be disinfected or wipe it clean to remove any debris before sterilization.
2. Prepare for Sterilization: Place the item to be disinfected on a flat surface, then place the UV Lid on top.
3. Select Disinfection Mode: Briefly press and hold the control button at the top of the device to power it on. Once on, press the control button twice to select the three-minute disinfection mode. The indicator light will blink during the process.
4. Completion: When disinfection is complete, the indicator light will stop flashing, and you can remove the UV Lid.
5. Repeat if Necessary: The device is now ready to sterilize another baby bottle or water cup.

1. Clean the Item: Wash the item to be disinfected or wipe it clean to remove any debris before sterilization.
2. Prepare the Container: Place the items to be disinfected into a container or bowl. If you want to sterilize the container or bowl itself, you can do so without placing any items inside.
3. Assemble the Device: Attach the silicone pad and the UV Lid by placing the UV Lid into the hollow center of the extension pad, with the ribbed side of the lid facing downward.
4. Set Up for Sterilization: Place the container or bowl on a flat surface and cover it with the assembled extension pad and UV Lid.
5. Select Disinfection Mode: Briefly press and hold the control button at the top of the device to start the default one-minute disinfection mode. For a three-minute disinfection, press the control button twice. The indicator light will blink during the process.
6. Completion: When the selected disinfection mode is complete, the indicator light will stop flashing.
7. Retrieve the Item: Remove the UV Lid and extension pad, then take out the disinfected item.
8. Repeat if Necessary: The device is now ready for the next disinfection cycle.